Magnum MMG100D Manuel de l'opérateur Page 43
- Page / 56
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
43
* Replace primary air cleaner when dust valve restriction indicator gauge shows a vacuum of 25 in. H
2
O.
** Change the oil and oil filter after the first 100 hours, then every 250 hours. If John Deere Plus 50 II engine oil
is used, the interval can be increased to every 500 hours.
ENGINE BREAK-IN REQUIREMENTS
Note: During the first 20 hours of operation, avoid long periods of no load or sustained maximum load operation. If
the generator is to run for longer than five minutes without a load, shut the generator down.
John Deere engines are supplied with engine break-in oil from the factory. Extra care during the first 100 hours of
engine operation will result in better performance and longer engine life. DO NOT exceed 100 hours of operation
with the break-in oil. Operate the engine at heavy loads (60-90% of maximum) as much as possible. If the engine
has spent significant time at idle, constant speeds and/or light load or if makeup oil is required, a longer break-in
period may be needed. Consult the engine operation and maintenance manual for a full description of necessary
procedures on the addition of break-in oil and extension of the break-in period. Use the schedule table above as a
guide for regular maintenance intervals.
EXHAUST FILTER SERVICE REQUIREMENTS
The exhaust filter system contains a diesel particulate filter (DPF). Over time, the DPF will require professional
servicing to remove ash buildup. The expected service interval will be at least 3000 or 4500 hours based on engine
power and operating conditions. Actual service should take place when the indicator light appears on the control
panel LCD. The DPF should be cleaned or replaced by an authorized service provider only. The removal of DPF
ash must be done by removing the DPF from the unit and placing it into specialized equipment.
CAUTION
Do not remove ash by using water or other chemicals. Removing ash by these methods
may cause equipment damage and create unsafe operating conditions.
CAUTION
Only a qualified service provider should remove, handle and dispose of diesel particulate
filters and ash. These materials may be considered hazardous under federal, state and local
regulations, and must be handled and disposed of properly.
To avoid unnecessary buildup of diesel particulates or soot in the exhaust filter system;
1. Utilize the Automatic (AUTO) Exhaust Filter Cleaning mode.
2. Avoid unnecessary idling.
3. Use proper engine oil. Refer to Engine Operator’s Manual.
4. Use only ultra low sulfur diesel fuel. Refer to Engine Operator’s Manual.
Check generator drive plate torque (see page 45)
Test thermostats
Replace air cleaner elements
Replace alternator and fan belts
Check fuses
Add coolant
Check electrical wiring and connections
Item Daily
250
Hrs.
500
Hrs./12
Months
3000
Hrs./ 36
Months
As
Required
- DIESEL GENERATOR 1
- MMG75D • MMG100D 1
- OPERATING MANUAL 1
- MAGNUM POWER PRODUCTS LLC 2
- TABLE OF CONTENTS 3
- SAFETY NOTES 6
- OPERATING SAFETY 6
- ENGINE SAFETY 7
- ELECTRICAL SAFETY 7
- TOWING SAFETY 8
- SAFETY SYMBOL SUMMARY 10
- SPECIFICATIONS - MMG75D 11
- SPECIFICATIONS - MMG100D 12
- UNIT DIMENSIONS 13
- UNIT SERIAL NUMBER LOCATIONS 14
- COMPONENT LOCATIONS 15
- AUTO EXHAUST 16
- FILTER CLEANING 16
- GENERATOR MONITORING 19
- ENGINE MONITORING 19
- RUN HOURS SCREEN 20
- ECU VALUES SCREEN 20
- BINARY INPUTS SCREEN 20
- BINARY OUTPUTS SCREEN 20
- WET STACKING 22
- FINE VOLTAGE ADJUSTMENT 22
- Figure A 23
- PRE-START CHECK LIST 24
- OFF MAN AUT 26
- SHUTTING DOWN THE GENERATOR 27
- Figure 1 31
- MDC CONTROLLER – HISTORY 32
- RUN CABLES THROUGH SLOTS 35
- VOLTAGE SELECTOR SWITCH 36
- EMERGENCY STOP SWITCH 38
- MAIN CIRCUIT BREAKER 38
- VOLTAGE REGULATION 38
- CUSTOMER CONVENIENCE OUTLETS 39
- DERATING FOR ALTITUDE 39
- REMOTE START TERMINAL BLOCK 39
- TRANSFER SWITCH 40
- BELT TENSION 41
- AUTO EXERCISE TIMER 41
- DAILY WALK AROUND INSPECTION 42
- ENGINE BREAK-IN REQUIREMENTS 43
- Central Lift Eye 44
- FUEL TRANSFER 45
- VISCOUS FAN CLUTCH OPTION 46
- 90250_A_03.13.13 47
- 90296_A_10.26.12 48
- 90415_E_03.19.13 49
- DC WIRING DIAGRAM 50
- INTERIOR 51
- 90302_A_11.06.12 52
- TRAILER WIRING DIAGRAM 53
- 90286_D_10.31.12 54
- SERVICE LOG 55
- PART NO: 32668 56
- 03.15.13 56
Produits connexes et manuels pour Générateurs d'électricité Magnum MMG100D
(76 pages)Teka HKE 535 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Öfen Teka HKE 535.
Wir stellen 1 PDF-Handbücher Teka HKE 535 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels